I want to thank you for your quick response in getting the part I ordered to me. I received it on Friday 11/05 and installed it the next day. It works just fine and when my wife is happy everyone in this house is happy.

Thanks again,
Loren P.

Installation successfully completed. Thanks for your support and the nice merchandise. We like the new racks better than the originals. Your prices are also more reasonable than the competition, for essentially the same products. Happy to provide an endorsement, if you use them.

Dave

MAYTAG Error Codes, Fault Codes

MAYTAG - Gemini Range/Stove/Oven Fault/Error Codes
MAYTAG - Type "C" and "D" Clocks Range/Stove/Oven Fault/Error Codes
MAYTAG - Range/Stove/Oven Fault Codes
MAYTAG - Stackable A/W and Dryer Fault & Error Codes

MAYTAG - Gemini Range/Stove/Oven Fault/Error Codes

Failure Code	Condition	Check/Repair
F0:-0	None
F1:-1	Runaway Cook Upper oven	Inspect oven temperature sensor, recommended to replace if needed
F1:-2	Runaway Cook Lower oven	Inspect oven temperature sensor, recommended to replace if needed
F1:-3	Runaway Clean Upper oven	Inspect oven temperature sensor, recommended to replace if needed
F1:-4	Runaway Clean Lower oven	Inspect oven temperature sensor, recommended to replace if needed
F1:-5	Keypad Cancel Upper	Check keypad, replace if necessary
F1:-6	Keypad Cancel Lower	Check keypad, replace if necessary
F1:-7	Keypad Disconnected	Check wiring between keypad and Electronic Range Control
F1:-8	Shorted Keypad	Check to see if steam or other moisture is getting into clock assembly. Replace keypad if necessary
F1:-9	Slave
F1:-A	Latch Switch, Upper	Inspect oven temperature sensor, recommended to replace if needed
F1:-B	Latch Switch, Lower	Inspect oven temperature sensor, recommended to replace if needed
F1:-C	Door Switch, Upper	Inspect door switch, recommended to replace if needed
F1:-D	Door Switch, Lower	Inspect door switch, recommended to replace if needed
F1:-E	EEPROM, Control	Recommended to replace Electronic Range Control
F1:-F	Jumper, Control
F1:-H	EEPROM, Read, Control	Recommended to replace Electronic Range Control
F1:-L	Oven temperature sensor, Track, Control	Inspect oven temperature sensor, recommended to replace if needed
F3:-2	Oven temperature sensor, Lower oven	Inspect oven temperature sensor, recommended to replace if needed
F3:-1	Oven temperature sensor, Upper oven	Inspect oven temperature sensor, recommended to replace if needed
F9:-1	Latch Lock Upper	Inspect oven temperature sensor, recommended to replace if needed
F9:-2	Latch, Unlock Upper	Inspect for obstruction in door lock mechanism
F9:-3	Latch Both Upper	Inspect for obstruction in door lock mechanism
F9:-4	Latch, Lock Lower	Inspect for obstruction in door lock mechanism
F9:-5	Latch Unlock Lower	Inspect for obstruction in door lock mechanism
F9:-6	Latch, Both Lower	Inspect for obstruction in door lock mechanism

Search for Maytag Appliance Parts

MAYTAG - Type "C" and "D" Clocks Range/Stove/Oven Fault/Error Codes

Failure Code	Condition	Check/Repair
F1	Supervisory relay enable shorted; sounds alarm and inhibits cook mode if alarm fault monitor is always active in non-cook mode, and needs to be unpowered till serviced	Usually a bad touch pad or clock assembly. Recommended to replace touchpad or ERC
F2	Bake-broil-clean temp runaway alarm; sounds alarm and resets control to non-cook mode when bake-broil-clean temperature exceeds programmed limits	Usually means a stuck relay. Electric @ 525F (bake), 640F(broil), 900F(clean) Gas @ 525F - bake, 640F - broil, 900F - clean
F3	Open temp oven temperature sensor; sounds alarm and inhibits cook mode	Recommended to replace oven temperature sensor
F4	Shorted temp oven temperature sensor; sounds alarm and inhibits cook mode	Recommended to replace oven temperature sensor
F5	Supervisory relay enable open; sounds alarm and resets the control to non-cook mode	Recommended to eplace electronic range control
F5	Missing AC line cycle detector; displays code	Unplug appliance for 2 minutes, that would clear the problem
F7	Function key shorted; too hot at the clock assembly or shorted touch pad or clock assembly	Recommended to replace touchpad or ERC
F8	Analog-Digital supervisory; sounds alarm to non-cook mode	Recommended to replace ERC
F9	Door latch supervisory	Unlock door and inspect the switches or clock assembly
F0	Key supervision cancel	Requires the removal of power until serviced. See qualified technician

Search for Maytag Appliance Parts

MAYTAG - Range/Stove/Oven Fault Codes

Failure Code	Condition	Check/Repair
F1	Touch pad or membrane is defective	Recommended to replace touch pad or membrane
F1	Watchdog on board	Recommended to replace touch pad or clock assembly
F2	Oven overheating	Recommended to replace relay board or bad oven temperature sensor
F3 or F4	Oven temperature sensor is open or shorten	Recommended to replace oven temperature sensor
F5	Hardware and watchdog circuits disagree	Recommended to replace clock assembly
F6	AC signal is missing	Inspect for proper voltage
F7	Function key shorted or jammed button	Recommended to replace touch pad or clock assembly
F8	Analog-Digital supervisory	Recommended to replace clock assembly
F9	Door latch supervisory	Inspect door lock circuit or recommended to replace clock assembly
F0	Function key jammed	Recommended to replace touch pad or clock assembly
* Here is a simple test that you can do to determine whether the clock or the touchpad are defective when the display reads F1: - Disconnect power to the range. - Gain access to the back of the ERC (electronic range control, or "clock"). - Unplug the touch pad ribbon connector from the ERC. This will be a flat wire about 1 ½" to 2" wide. - Make sure everything is clear and will not short out when power is turned back on. Replace any covers removed to gain access to the ERC. - Turn the power back on to the range. - Watch for the F-1 and listen for the beep. - If you get the F-1 and beep, replace the ERC. - If after approximately 60 Minutes you do not get the F-1 fault, replace the touch pad. NOTE: Some models incorporate the touch pad and the clock control as one part so F1 = bad clock control. Warning: If you do not feel comfortable doing this test or making this repair please contact a qualified appliance repair technician.

Search for Maytag Appliance Parts

MAYTAG - Stackable A/W and Dryer Fault & Error Codes

Failure Code	Condition	Check/Repair
"L" persists in washer display	Failure of lid lock	Recommended to replace switch, linkage, lock solenoid or control board.
1E persists in washer display	Failure of lid lock	Replace lid lock switch or control board.
9E appears in dryer display	Failure of door switch	Inspect door switch wiring or door switch or control board
"U" occurs for no reason in display	Unbalanced load	Unbalance switch or control board
6E appears in dryer display	Temp control error	Ambient at room temperature too cool, -or- · Thermistor · Wire harness · Control board
7E appears in dryer display	Temp control error overheating	Inspect: · Venting for restriction · Thermistor · Control board · Cycling thermostat
8E appears in dryer display	Motor relay circuit	Check: · Relay coil · Wire harness or · Control board

Search for Maytag Appliance Parts

0 items in your cart

$0.00 total

30 Days Returns

Free Repair Video

Same Day Shipping

Lowest Price

Special Deals from us: