I want to thank you for your quick response in getting the part I ordered to me. I received it on Friday 11/05 and installed it the next day. It works just fine and when my wife is happy everyone in this house is happy.

Thanks again,
Loren P.

Installation successfully completed. Thanks for your support and the nice merchandise. We like the new racks better than the originals. Your prices are also more reasonable than the competition, for essentially the same products. Happy to provide an endorsement, if you use them.

Dave

GE (General Electric) Error Codes, Fault Codes

GE - Gas or Built In Oven Fault Codes
GE - XL44 Self Clean Oven Fault Codes
GE - "New '99" Range/Stove/Oven Fault Codes
GE - Range/Stove/Oven Fault Codes
GE - WSL Model Washing Machine
GE - Microwave Fault / Error Codes
GE - Dishwasher Fault/Error Codes - From Late 1990's forward

GE - Gas or Built In Oven Fault Codes

Failure Code	Condition	Check/Repair
F0 or F1	Failed transistor in control	If code cannot be deleted, recommended to replace the Electronic Range Control or touch pad
F2	Oven over temp - exceeded 590F with door in unlocked position or 990F with door locked	If actual temp condition occurred, look for welded relay contacts or high resistance connection or any cause in the oven temperature sensor circuit
F3	Open oven temperature sensor circuit	Determine oven temperature sensor circuit at oven temperature sensor should be approx 1100 ohms at room temp, check wire connections
F4	Oven temperature sensor circuit shortened	Check for melted connector or both leads shorted to ground
F8	Component failure in Electronic Range Control effecting temperature processing circuits	Recommended to replace Electronic Range Control
F9	Problem with door lock circuit such as pinched wire between door lock switch and Electronic Range Control	Inspect wiring and test operation of switch

Search for GE Appliance Parts

GE - XL44 Self Clean Oven Fault Codes

Failure Code	Condition	Check/Repair
F0 - F1 - F7	Stuck keypad can be that the relay is turned on.	Resolve if the problem is with the Key Panel or Control by: 1. Press CLEAR/OFF button. 2. Disconnecting Ribbon Cable from control and waiting at least 32 seconds to see if Code reappears If code reappears, problem is in the control. Recommended to replace control. If code does not reappears, problem is with the Key Panel.
F2 Note: Also see fan thermal switches	Indicates that oven is overheating in one of the following modes within either a clean mode of operation or cooking · Control senses that oven temperature is above 650F degrees with the door circuit in the unlock mode. · Control senses that oven temperature above 935F degrees with the door in the locked mode. · Airflow or stalled cooling fan problem.	· Search for welded relay contacts. · Search for open thermal switch in lock motor circuit. Switch is normally closed and will open if area overheats due to fan not operating. Search for cause - fan thermal switch not closing, fan stalled · Search for high resistance in the oven temperature sensor circuit due to high contact resistance or intermittent solder joint on control or intermittent oven temperature sensor · Search in the oven temperature sensor circuit for electrical noise interference
F3 - F4	Open oven temperature sensor over 2700 ohms or, oven temperature sensor is shortened. Could be the result of: · contamination on terminals · strained wire in oven temperature sensor circuit · cold solder joint on control.	· Remove oven temperature sensor connector from control. Make sure the power is disconnected · At the oven temperature sensor connector measure oven temperature sensor resistance but be careful not to damage the terminals in the block. It should read 1100 ohms at room temperature · Measure oven temperature sensor that leads from connector block to ground. If the sensor is shorted, look for pinched or cut wire in oven temperature sensor circuit · Inspect connector terminals - Look for bents or rust on terminals. Repair or replace If nothing works recommended to replace control
F5	Failure of the relay safety circuit	· Inspect oven temperature sensor circuit for intermittent high resistance. · Inspect lock circuit · Preprogram the control by pressing Clear/Off and If the code comes back, recommended to replace control *If everything is okay than it might just be a momentary loss of power, no need to replace the control
FC	Problem with the door lock switches on motorized lock circuit and door lock circuit contains stained wires between control	Check wiring and test operation of switches.
FD	Meat probe shortened *Problem can be with the probe meat probe circuit or receptacle	· Check probe. Resistance should be 30k ohms to 50k ohms at room temperature. · Look for pinched wire. · Look for condensation or contamination of receptacle or nearby installation.
FF	Loss connection in the door motor safety circuit	Recommended to replace control

Search for GE Appliance Parts

GE - "New '99" Range/Stove/Oven Fault Codes

Failure Code	Condition	Check/Repair
FFF	Control Error, Failed EEPROM	Recommended to replace Control
F0 or F7	Clear/Off key is shortened due to membrane switch, connector or control	Shorted key panel membrane switch; Check Electronic Range Control (ERC)
F2 During Bake	Control senses oven temp above 590F degrees	High resistance connection in oven temperature sensor circuit. Inspect the Electronic Range Control and also the welded bake relay contacts
F2 During Clean	Control senses oven temp above 915F degrees	High resistance connection in oven temperature sensor circuit. Inspect the Electronic Range Control and also the welded clean relay contacts. Both lock switch 1 and 2 should be closed at the same time
F3	Open oven temperature sensor, oven temperature sensor resistance exceeds 2900 ohms during bake, clean or broil	Oven temperature sensor circuit connections or oven temperature sensor
F4	Oven temperature sensor shorted, oven temperature sensor resistance less than 2900 ohms during bake, clean or broil	Oven temperature sensor circuit connections or oven temperature sensor
FFF	Door motor safety circuit	Electronic Range Control

Search for GE Appliance Parts

GE - Range/Stove/Oven Fault Codes

Failure Code	Condition	Check/Repair
F0 and F1	Thermistor Control failure	Recommended to replace Electronic Range Control
F2	Oven temperature exceeds 590F with unlocked door	High resistance or interference in oven temperature sensor. Recommended to replace oven temperature sensor
F3	Open oven temperature sensor circuit	Recommended to replace oven temperature sensor
F4	Wire shortened in the oven temperature sensor	Find and fix
F7	A = Function pad button jammed or B = Bad clock	Un stick button or recommended to replace Electronic Range Control
F8	Failure of the component	Recommended to replace Electronic Range Control
F9	Program the door circuit	Inspect wiring

Search for GE Appliance Parts

GE - WSL Model Washing Machine

Failure Code	Condition	Check/Repair
IE - Water level sensor error	Water sensor fails to send signal for longer than 5 seconds	Press POWER button. If no other buttons are working: · Inspect wiring harness · Inspect pressure sensor switch · Inspect circuit board
7E - Water supply error	For 60 minutes no frequency was changed from water supply	Press POWER button. If no other buttons are working: · Inspect wiring harness · Inspect water valve Inspect pressure sensor switch · Inspect circuit board
E - Drain pump error	Water level doesn’t reduce to reset point within 15 minutes from draining water from the washer	Press POWER button. If no other buttons are working: · Inspect wiring harness · Inspect pump motor · Inspect circuit board
dE - Lid open error	Open lid during wash cycle	Close lid. · Inspect wiring harness · Inspect lid switch · Inspect unbalance switch · Inspect circuit board
UE - Unbalance switch error	Unbalanced load is sensed three times during a spin operation	Open lid. Rebalance laundry load and close lid. · Inspect wiring harness · Inspect unbalance switch · Inspect circuit board
OE - Water overflow error	Water supply doesn’t stop after sensing an overflow condition	Turn off household water supply to washer and unplug the power · Inspect wiring harness · Inspect water inlet valve · Inspect pressure sensor switch · Inspect circuit board

Search for GE Appliance Parts

GE - Microwave Fault / Error Codes

Failure Code	Condition	Check/Repair
F1	Open sensor, will occur below 190F of cavity temperature within 15 minutes after starting convection, combination or roast cook	Inspect oven temperature sensor for continuity. Recommended to replace if zero or infinite ohms
F2	Thermal sensor shortage will occur if a shorted thermal sensor is detected continuously over 5 seconds on convection, roast cooking or combination	Inspect oven temperature sensor for continuity. Recommended to replace if zero or infinite ohms *It will take a about of 5-8 minutes of convection run time before F1 or F2 code will be displayed if the thermal sensor is open or shorted
F3	Key panel shortage will occur if a shorted key panel is detected incessantly over 60 seconds	Recommended to replace key panel
F4	If humidity sensor is detected as being open incessantly over 5 seconds than the humidity sensor is open	Recommended to replace humidity sensor
F5	Humidity sensor shortage will occur if humidity sensor is detected as being shorted incessantly over 5 seconds	Recommended to replace humidity sensor
F6	Temperature probe shortage will occur if temperature probe is detected as shorted incessantly over 5 seconds	Recommended to replace temperature probe
ProbEe	Open temperature probe, will occur if temperature probe is detected open or not plugged into the receptacle	If probe is plugged in and "ProbE" is on display check stability of the probe with an ohm meter. If zero or infinite ohms, recommended to replace probe

Search for GE Appliance Parts

GE - Dishwasher Fault/Error Codes - From Late 1990's forward

Failure Code	Condition	Check/Repair
PF	Power Failure	Push cancel to clear. If code persists check electrical connections to dishwasher and electronic control
C1	Partially restricted drain, pump-out not accomplished in the normal time of less than 95 seconds	Inspect drain line, if clear, inspect for a restricted drain valve in pump
C2	Drain line blocked, pump-out not consummate in the maximum time of 405 seconds	Inspect drain valve for restriction in pump, inspect drain line. *If a new garbage disposer was installed, get rid of the knock out plug for dishwasher drain
C3	No drain	Call for service
C4	Water over-fill fault	Inspect for high water pressure to unit, usually a sign of a bad water inlet valve
C5	Water fill is low	Inspect for low water pressure to unit, usually a sign of a bad water inlet valve
C6	Water temperature is too low after 20 minute extension	Inspect heating element and thermostat, both of them should have stability
C7	Bad temperature sensor	Recommended to replace sensor
C8	Blocked detergent cup	Keep items clear of cup when loading

Search for GE Appliance Parts

0 items in your cart

$0.00 total

30 Days Returns

Free Repair Video

Same Day Shipping

Lowest Price

Special Deals from us: